Door cover large installation tool and installation process

The door cover is a functional interior component that acts as a decorative door and door frame and echoes the wall decoration. However, the complicated door sets are easy to give people a messy feeling, especially in small rooms. Therefore, the current door covers are usually designed to be narrower and simpler. Its protective effect is more than decorative effect. Generally, it depends on the specific design requirements to decide whether to use it. The main function is to prevent wall damage. The detailed process of installing the door cover is described below.

Tools/Material Tools: Small wooden wedges, hammers, hinges, steam gun nails, nails, planes, hangs, sealants, impact drills, tape measures

Step / Method 1. Check the door specifications, opening direction, related accessories, etc. according to the design drawings. Use a tape measure to measure the height and width of the door opening. The standard height and width dimensions of the door are 200 cm x 80 cm; the door height of the bathroom is 200 cm x 70 cm. If the size is different, it should be corrected in time. Measure the position line, determine the position of the door frame, pull out the vertical line with the ink cartridge, and two vertical lines on one side of the door.

2. Drill the eye with a percussion drill on the vertical line. The distance between the eyelet and the eyelet is about 30cm, and there are 10 holes in the two rows of the side door. The impact drill should have a drill bit of 12 mm and a drilled eye depth of approximately 6 cm.

3. Screw the small wooden wedges into the holes one by one with a hammer to fix the door frame. The size of the small wooden wedge is 5cm × 1.5cm × 1.5cm, which is better made with larch, because the wood structure of the larch is tight and it is not easy to loosen.

4. Open the door frame. The size of the wood board that makes the side frame keel on the left and right sides is 200cm×3cm×8cm, and the size of the wood board of the top keel of the door frame is 80cm×3cm×8cm. The high-density nine-centre plate is glued to the keel and fixed with a gas gun nail. The three frame frames that have been made are joined in the shape of the door and fixed with a large nail at the joint. Use a plane to smooth the surface of the connected door frame, trim the corners, and sharp edges and corners.

5. Place the door frame on the door hole, according to the horizontal line of the wall. Take the wood or brick under the door frame to adjust the height of the door frame. Reserve 5cm below the keel buried in the floor. A nail is placed on the top of the door frame, the line is hung up, and the vertical direction of the door frame is adjusted by the hanging line. While measuring the side, the door frame is fixed on the door hole with a twisted nail.

6. Make the lines of the door face. The door face can be bought off-the-shelf or it can be made by the construction personnel according to the drawings. After the production is completed, the door surface is fixed to the door frame six, so that the door cover is basically completed.

7. Put the door on the door cover to make a better position, determine the specific position of the hinge on the door cover, and then cut the exit diameter according to the thickness of the hinge. Also cut out the size of the lock sleeve. Install the door on the door cover and tighten the rivet with a twisting knife. Note that the clearance between the door and the door cover should not exceed 1.5mm, which is subject to smooth opening and closing.

Cautions 1. Do not place heavy objects on the door frame or hang them in the frame fan to prevent deformation and damage.

2. When handling, apply non-metallic soft material pad on the surface, and choose a firm and stable point to avoid scratching the door surface.

3. During the installation process, the surface of the cement mortar, sealing paste, etc. should be cleaned in time to protect the surface quality.

4. The door corner line corner joint is tight, the groove is smooth, the texture and color change are not big, the fixing should be firm, the nail eye should be nailed as far as possible in the line strip, and the line is 2MM away from the ground.

5. Before using the door panel, it is necessary to select a smooth and smooth (deburring) primer and classify the reasonable kit and use it together. The sealing plate is white latex and fixed by mosquito nails. [ WeChat public number "Jiuzhengmen window net", pay attention to courtesy, scan code to send millions of business opportunities! Jiuzhengmen window network exchange group ]

Ningbo GDoor three/four-wing Automatic Revolving Door is the other revolving door category in Ningbo GDoor revolving door family. Three/four-wing automatic revolving doors is elegant and economical. Except for the entry and exit of busy passing traffic, GDoor three/four-wing revolving doors marks the highest standards in wind-proofing, dustproofing, warm-proofing and energy-saving aspects, which exceeds customers' and architects' expectations. Ningbo GDoor three/four-wing automatic revolving doors come in two driving models: top driving and underground driving.

Three/Four-Wing Automatic Revolving Door Set

Three/Four-Wing Automatic Revolving Door Set,Security Revolving Doors Set,Glass Revolving Door Set,Darkroom Revolving Door Set

Ningbo Gdoor System Control Technology Co., Ltd. , http://www.gdoor-cn.com