Toolkit can be used to maintain occupational safety
The Liaoning Province Federation of Trade Unions and the Provincial Administration of Work Safety jointly held the launching ceremony of the “Promotion and Application of the ILO Occupational Safety and Health Protection Toolkit for SMEsâ€, which will use three years to introduce international advanced occupational safety protection concepts for small and medium-sized enterprises in the province. And skills to maintain the occupational safety and health of SME workers.
The ILO addresses the widespread occupational safety and health problems in the workplace of small and medium-sized enterprises, sums up and formulates a set of solutions covering nine categories and 132 items. This program is called a "tool kit." The All-China Federation of Trade Unions has promoted the "Toolkit" as a concrete measure to serve employees and service enterprises, and has identified our province as the first province to promote and apply.
The relevant person in charge of the Provincial Federation of Trade Unions stated that the province plans to use it for three years to promote the use of the “tool kit†project in the province. The first batch of 30 pilot enterprises has been identified, involving locksmiths, milling cutters, welders, masonry workers, spray painters. There are 12 major types of work, including sewing and weaving workers, weavers, hoisters, maintenance workers, packers, heat treatment workers, and distribution and distribution workers. It covers 13,557 small and medium-sized enterprises and 946 crews. These companies will formulate feasible improvement measures, form a perfect occupational safety and health checklist and inspection points for the unit, and accumulate practical experience for the wide application of the “toolkit†throughout the province and even the whole country.
The Installation of Mounting Unit
1. Make the concrete base according to solution drawing, locate embedded bolts and set out strings by Laser Level to ensure the centers of embedded bolts in the same elevation as accurate as possible on vertical, horizontal direction and at end face.
2. Locate the Anchor Plate on the concrete base and adjust the position according to solution drawing(remove M14 washer,M14 spring washer,and M14 nut if they are connected to embedded bolts now),and then fasten M14 washer, M14 spring washer, and M14 nut with the tightening torque of 60N.m.
3.Take out the Hexagon Bolt Kit with Post B Corrugated Gasket M12x95 and remove its nut, spring washer, one washer, and corrugated gasket. Insert the Post A, B, C in to Anchor Plate according to the Hexagon Bolt Kit with Corrugated Gasket M12x95 drawing and then fix them by two sets of Hexagon Bolt Kit with Corrugated Gasket M12*95. Post C Post A
4.Remove the bolt kits M12*90 from all the Posts and Pre-Assembled Supports and unfold the embedded Supports, fasten them on the Posts by bolt kits M12*90 according to the drawing.
Installation of Rails
1.Please check the length of Beam before place it onto the Pre-Assembled Supports, otherwise extend it with Splice forBeam first. There are 4 self-tapping screws in each side and total 8 self- tapping screws in both sides. We strongly recommend NOT extend the Beams on Preassembled Supports.
2.Before locate the Beams, mark the position of the Beam son the surface of Pre-Assembled Supports with maker pens according to solution drawing for easier installation. Place the Beams on the 55*80 Tube of Pre-Assembled Supports and fix it with C Clamp Kits. Install all the Beams in the same step. The tightening torque will be 20N.m. C Clamp Kit Side Beam(Please arrange 3-4 persons to install when the array is long.)
Installation of Solar Panels
1.Place the panels above the Beam 85, fixing it with Wide End Clamp Kit in the side and Inter Clamp Kit in the middle. Install all the panels in the same steps until complete installation of al panels. Fasten all the bolts with tightening torque of 10N.m.
2.Complete installation, and please inspect and make sure all the bolts are fastened.
Solar Mounting System For Green House
Solar Panel Mounting Frames,Solar Panel Mounting Systems,Greenhouse Solar Mounting System,PV Mounting Systems
Hebei Honde Plastic & Metal Co., Ltd. , https://www.foundation-system.com