The reason for the nine common problems of bearing
| Home>Bearing knowledge>The reason for the nine common problems of bearing |
The reason for the nine common problems of bearing
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
It is not uncommon for the bearing to appear faulty during the operation; therefore, it is not rare to present it. It is a problem; discrimination and disposal are the key points. Today we will explain the common causes of FAG bearings.
1, the bearing temperature is too high: in the organization of the work; the part of the bearing of the device promises a certain temperature; when the hand touches the tissue shell; should not feel the trick is normal; otherwise it indicates that the bearing temperature is too high.
The reason why the bearing temperature is too high is that the smooth oil quality does not meet the demand or the enthalpy change; the smooth oil viscosity is too high, the tissue device is too tight (the gap is lacking), the bearing device is too tight, the bearing race is changed on the shaft or the shell, and the load is over Large, bearing cage or rollover fragmentation.
2, bearing noise: Rolling bearings in the operation promised a subtle work noise; if the sound is too loud or there are abnormal noise or impact sound; then indicate that the bearing is faulty.
The reason for the noise of the rolling bearing is more complicated; 1) it is the external wear of the inner and outer rings of the bearing. Because this is worn, the cooperation between the bearing and the shell, the bearing and the shaft is broken; the axis is deviated from the correct orientation; When the shaft is moving at high speed, abnormal noise occurs. When the bearing is exhausted; its appearance metal falls off; it will also increase the radial gap of the bearing and cause abnormal noise. 2) The bearing is lacking in smoothness; the dry conflict is formed; and the bearing is broken, etc. The movement is static. 3) After the bearing wears loosely; the cage is loose and damaged; the damage of the abnormal bearing will also occur. When the rolling bearing is disassembled and viewed; the bearing fault and damage cause can be judged according to the damage condition of the bearing.
3. The metal surface of the raceway is detached: the bearing tumbling body and the inner and outer ring raceways all receive the effect of periodic pulsating load; then the contact stress changes during the attack cycle. When the number of stress cycles reaches a certain value; in the rollover or The inner and outer ring raceway work surface is fatigued and shedding. If the bearing load is too large, this fatigue will be aggravated. Others; the bearing device is not correct, the shaft is tortuous; the raceway will be off the surface. The bearing raceway Excessive fatigue will reduce the accuracy of the shaft operation; make the tissue oscillation and noise. Imported pump valve 4, bearing burn: burned bearings have tempering color on the raceway and roll body. The cause of burn is usually smooth lack, smooth oil The quality does not meet the demand or transformation; and the bearing device is too tight.
5. Plastic deformation: the bearing raceway and the roller touch surface show uneven pits; clarify the plastic deformation of the bearing. The reason is that the bearing is under the effect of large static load or impact load; The yield limit of the data; this condition usually occurs on bearings that rotate at low speeds.
6, bearing seat crack: the cause of cracks in the bearing seat can be too tight bearing cooperation; bearing foreign or inner ring loose; bearing housing deformation; equipment bearing surface processing is not good.
7. The cage is broken: its cause is smooth lack; the rolling body is broken; the seat is inclined.
8. The metal of the cage adheres to the tumbling body; the reason for the ability is that the tumbling body is stuck in the cage or is lacking in smoothness.
9, the raceway raceway is severely worn: it can be a foreign object falling into the seat; the lack of smooth oil or the smooth oil trademark is not suitable.
Recommend to friends comments close window
| Bearing related knowledge |
| Common bearing types on machine tools INA bearing uses the oil smooth strength to replace the roller bearing when the bearing is concerned about the terminology of the bearing professor: the bearing ring casting "common equipment" |
This article links to http://
Please indicate the bearing network http://
Previous:Linear bearing features Next: Correct use of rolling bearings and common problems
Cold Storage Room Fast Door are used to industrial warehouse applications, our cold storage doors combine the latest technology, premium materials and design features to meet the demanding requirements of the cold storage industry. Available as a sliding, swing and vertical lift door, all Cold Guard doors incorporate a tough and thermally neutral fiberglass reinforced pultrusion framework, extruded plastic polymer casings and Non-CFC foamed-in place polyurethane core. We understand the conditions that cold storage doors must endure. Superior design methods and non-corrosive materials ensure that Cold Guard will perform and look good for years to come!
The advantages of cold storage fast room door
Excellent Insulation Properties
Save Money on Temperature Costs
A Variety of Cold Room Options
Temperature Control and Efficiency
One of the most important benefits of our cool room panels is passive temperature control.
Safety for You Too
Not only are our cold room panels very hygienic, they also allow for superior safety. Their low allergenic qualities and enhanced seismic performance will protect you while you`re at work.
Cold Storage Room Fast Door
Cold Storage Room Fast Door,Freezer Room Fast Door,Freezer Room Insulated Fast Door,Thick Curtain High Speed Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hongfadoor.com