Hydropower renovation construction process renovation water and electricity precautions
Hydropower transformation is the first step in home decoration, and it is also the most important basic step related to home life in the future. However, for most non-professionals, it is not clear what is irregular construction when they conduct hydropower acceptance. There are some places to pay special attention to check, today's home decoration network Xiaobian will come to tell you about the renovation of water and electricity , I hope to bring some help.
Renovation of hydropower notes:
1. Strong and weak electricity should be differentiated by using different color conduits for future maintenance.
2. The arrangement of all the conduits is best “horizontal and verticalâ€. For some families with limited budget, there is no big safety hazard when using the obliquely staggered wiring method, but the position of the conduit should be kept in mind to prevent the wall surface. Drilling holes, nails, etc. cause damage to the line pipe.
3. When the strong and weak wires and tubes cross the phase, use tin foil to wrap one of the conduits. This can avoid the interference caused by mutual interference, and can also protect the intersection of the conduits and reduce wear.
4. The connecting sockets of the strong and weak lines on the wall should be separated by 15-30cm, which is more convenient to use and can avoid mutual influence.
5. When the circuit is wired, the angle of single wire tube ≤90° can't be more than three. When the angle is more than three at ≤90°, it is difficult for a single wire to be pulled out from the line pipe when replacing the wire in the future. Causes breakage of the wire.
6. At present, the size of the line tube commonly used in home decoration is 4 points and 6 points. Generally, 6 tubes are used. It should be noted that there should be no more than 5 wires in 6 tubes, otherwise the wires inside the tube will be tightly entangled together. Maintenance caused trouble.
7. The wires on the ceiling in the kitchen and bathroom space should be reserved for 10cm outside the line, which is used to connect electric lights, Yuba and other equipment. At the same time, all the wires outside the line are protected by hoses to avoid the wires outside the line. Loss, increase wire life.
8. In addition, it is necessary to make color separation when purchasing wires before decoration. It is better to choose different color wires for strong and weak wires and ground wall wires for future maintenance.
Two major considerations for waterway acceptance:
9. The hot and cold water pipes should be slotted separately and separated by more than 10cm from each other to avoid mutual influence. (The special reminder here is that the slotting cost of one slot and two tubes and two slots is the same.)
10. When the water pipes parallel to the wall are fixed by pipe clamps, the pipe clamps should be spaced apart from each other by ≤1m. Otherwise, the water pipes will sway when the water flows, and noise will be generated, which will also reduce the service life of the water pipes.
Hydropower contains two important factors: safety and concealment. Any care in the early stage and construction process cannot be overemphasized.
The above is the introduction of the decoration water and electricity precautions brought by everyone in the decoration home network Xiaobian. If you need to know more information, please continue to pay attention to our home encyclopedia!
More related wonderful reading:
The basics of decoration plumber installation that we should know when decorating
How much is the renovation cost of new house renovation and hydropower renovation?
What should I do for indoor decoration and water installation? Install detailed method steps
What are the precautions for renovation of hydropower? What is the price of hydropower transformation?
What preparations do you need to make to renovate hydropower?
Corrosion-Resistance Alloy,mainly refers to ordinary stainless steel resists atmosphere and sea water corrosion such as 300 series stainless steel including 304,316L, 317L etc.; comparatively strong corrosion resistance material including austenitic stainless steel 904L, 254SMOand Dual phase steel 2205,2507 etc.; Corrosion Resistant Alloy containing Cu 20 alloy; In comparison to non-metal corrosion resistant materials, corrosion-Resistance Alloy main refers to iron alloy (resistance to corrosion); nickel alloy (Ni-Cr alloy, Ni-Cr-Mo alloy, Ni-Cu alloy and other active metal.
Corrosion-Resistance Alloy
Corrosion-Resistance Alloy,Corrosion-Resistant Alloy Tube,Corrosion-Resistant Alloy Welding Wire,Corrosion-Resistant Nickel-Chromium Alloy
Jiangsu nickel alloy Co.,Ltd , https://www.xhalloy.com